This machine is a Automatic Solder Paste Mixing Equipment.Size:390 x 390 x385
1.Professional SMT Digital has Strong mixing ability,satisfy ISO-9000 cream mixing conditions.
2. Attached red rubber fixture,can be used as red rubber claves.
3.Micro-computer digital control,easy operation.
4. SMT Solder Paste Mixing machine has strong adaptability,with all-purpose fixture,suitable for various brands of cream.
5. Multiple security protection,ensure the safe operation.
6. Operated speed:480RPM
7. Work ability: 100-1000g, put two bottles at the same time.
8.Mixing time:0.1-9.9minutes.
Stirring a variety of solder pastes such as ISO-9000, can be used as a red glue decreate.
Any details about Solder Paste Mixing machine you want to know please contact us for further more.
SMT Solder Mixer,Solder Paste Mixing Equipment,Solder Paste Mixing Machine,Solder Pasting Mixer,strong mixing ability SINGSUN ELECTRONIC SCIENCE & TECH CO.,LTD , https://www.szsingsunautomatic.com
There are 7 kinds of solutions to the malfunction of the regulating valve during operation. During the operation of the regulating valve, there often occur such problems as jamming and jamming. Some even happen when they are put into operation. We have summarized some reasons and solutions For reference. 1, cleaning method Pipe in the welding slag, rust, slag, etc. in the throttle, guide parts, under the valve cover to balance the hole caused by blockage or stuck so that the valve surface, guide surface tension and scratches, sealing surface On the indentation and so on. This often occurs in the early delivery of new delivery systems and overhauls. This is the most common failure. In this case, you must uninstall the cleaning, remove the slag material, such as the sealing surface is also damaged should be ground; at the same time the bottom plug open to flush away from the balance hole into the valve cap slag material, and the pipeline Rinse. Put into operation before the valve is fully open, medium flow into the normal operation after a period of time. 2, external scouring method For some easy to sediment, the medium containing solid particles using ordinary valve adjustment, often in the throttle, the guide block, can be flush at the bottom of the bonnet flushing gas and steam. When the valve is clogged or stuck, open the external gas or steam valve, you can complete the flushing work in the case of the valve does not move, so that the valve normal operation. 3, the installation of pipe filters on the small-caliber control valve, especially the ultra-small flow control valve, the throttle clearance is very small, medium can not have a little slag material. In this case of blockage, it is best to install a filter on the valve before the pipeline to ensure the smooth passage of media. Control valve with locator, locator is not working properly, the air passage choke plug is the most common failure. Therefore, with the locator work, you must handle the gas source, the commonly used approach is to install the air filter regulator in front of the gas locator 4, to increase the throttle gap method such as the media of solid particles or pipes Washes off the welding slag and rust, etc. due to over throttle can cause blockage, stuck and other failures, can be used to throttle large gap throttling pieces - throttle area for the window, the opening of the spool, sleeve Tubes, because of their concentrated throttle area rather than their circumferential distribution, can easily be ruled out. If it is single, two-seater valve plunger can be changed to "V" -shaped spool, or into the sleeve valve. For example, a chemical plant often have a double-seat valve stuck, it is recommended to switch to sleeve valve, the problem was resolved immediately. 5, medium scouring method using the medium of its own scouring energy, erosion and easy to take away sedimentation, easy to block things, thereby enhancing the anti-blocking valve function. Common methods are: ①closed for the flow of closed-type use; ② the use of streamlined body; ③ the throttle placed in the erosion of the most powerful, using this method should pay attention to improve the erosion-resistant materials, parts erosion. 6, Straight through to the angle method Straight through the inverted S flow, flow path complex, upper and lower cavity dead zone, provides a place for the precipitation of the medium. Angular connection, like 90 ° elbow flow through the medium, erosion performance, small dead zone, easy to design streamlined. Therefore, the use of straight through the control valve can be slightly blocked when the valve can be used to change the angle 7, for the steam pipe valve sleeve, if the spool and sleeve gap is too small, or use different materials, it is likely because of expansion Coefficient of the different heat stuck. You can increase the gap in the appropriate processing (to meet the flow control requirements as a prerequisite), to prevent the occurrence of similar situations. More keyword search: Regulating valve